
The one slowly falling into place really got my juices flowing
Surely if it was truly gapless it would have hovered on the cushion of air.
That sounds so dirty yet I can't think of a better way to put it. Please accept my upvote.
6 more replies
Same. Got some weird looks in the office, but still totally worth the watch.
I hope those are made for the sole purpose of being satisfying because it fucking works, I am fully satisfied now.
1 more reply
The very last one ruins it. You can clearly see the seam.
The video stops right as they connect -- I wonder whether they just haven't fully pushed the pieces together yet, and it just needs to show another second of it. Some of the others have a seam when they first connect, but it then disappears once they apply a little pressure.
Here is the missing frame and it is up to someone to put it together because i dont know how to
Comments like this is what makes me watch the whole thing
You're so right! I was about to bust a real big fat sigh of satiscation. Then that last one left me blue and sore. So close.
5 more replies
With tolerances that tight, how hard it is to pull them apart again?
Harder than my dick while watching this video.. so yeah pretty hard.
I’m no expert but it looks like it should only take as much pull weight as the weight of the piece itself that went in naturally with no extra pushing. So as long as you pull it out at the same speed as it went in, it shouldn’t be too hard.
1 more reply
i have never nutted so many times in such a short amount of time
1 more reply
For those that might not have considered it...
These are two separate pieces. It's not as easy as just cutting one piece in half in an intricate pattern, because the cutting tool removes material.
Also if you are unfamiliar with machining... To get a finish like this, it requires multiple processes. You would have an end mill rough out the shape and leave about 0.005". Then you have a very fine finishing end mill come in and remove the remaining 5 thousands of an inch (less than the thickness of a human hair).
Then to get a perfect finish, they likely leave about 0.0002" to be polished off.
To have them fit this perfectly, there is extremely little room for error. For instance, if one piece was sitting on a table and thr other piece was handled too much, the heat transfer from human touch could expand it enough to make it not fit.
Also a fun fact (that I assume is fact because I have never been able to verify it for obvious reasons), if you have two pieces of metal like this with a perfect finish and you take them into space where there is no air between them and mate them up, they will "weld" together and be inseparable. That's what I was told in school anyway.
Metals don't cold weld on earth because they form a very thin oxide layer on the surface. You would need to machine these pieces in space/vacuum, then they can cold-weld once they touch.
9 more replies
I was able to find a very similar video: https://www.youtube.com/watch?v=NH8ZE4UqAb8
It is indeed precise 3-axis milling, although I understand why EDM is most people's first guess.
8 more replies
3 more replies
pretty easy, the parts are shaped so that air doesn't get trapped.
1 more reply
This is probably wire EDM and not traditional CNC machining.
Not many of these are features capable of being wire edm'd. Sinker edm'd sure. But these are all ground afterwards, which makes me a touch suspicious.
source: Am a machinist that does some wire edm work, but certainly no expert on the topic.
A couple months ago the title said this is EDM and people were quick to point out it is indeed 3 axis milling and not EDM. Now the title of the exact same post says CNC and people are quick to say it's EDM.
I see this gif about once every two month and every time someone in the comments section says it’s probably EDM.
They’re not EDM. They’re milled on a JingDiao. The sample parts even say JingDiao on them if you had any doubt. JingDiao even puts full-page adverts in most Modern Machine Shop issues that say “Not EDM” because they are aware of this misconception.
I’m getting so tired of making this comment that next time I have an in-person meeting with JingDiao I’m going to special request a YouTube video that says not EDM.
This video is literally a demonstration for a milling machine. It's not EDM.
There are lots of videos like this on their youtube channel. https://www.youtube.com/watch?v=lREuqjodfAU
4 more replies
I take it that CNC also means something not related to sex?
2 more replies
You people are so crazy. My dad is a tool & die maker who actually produces things like this. I always wondered what the satisfaction was regarding it. Seeing it in action, now I know why he is still working at 79.
1 more reply
To demonstrate the ability and precision of the machine that made it.
It's probably wire EDM, which can get down to the 0.001mm range.
Air tight gallery tolerance is normally in the sub.0005" category.
No idea the tolerance necessary,but the company that engraved the etch6ongs on the side is a super high accuracy mill manufacturer
Micron or sub Micron. As a sales demo they'll drill a hole and engrave your name into one of your hairs and show you the end result on a microscope.
The clip with the 3 twisting ones never showed any of them go fully down and I'm actually angry about it.
2 more replies
Members
Online

